1933-1934 Ford Car
Search Categories
- { Out of Stock }
Dropped Steering Arms
$125.00
- Stocking thousands of New and Original 1933-1934 Car parts
- Stock Original & Early Style Hot Rod Parts
- Early Ford Store - San Dimas, California
- www.EarlyFordStore.com
- phone (909) 305-1955
- email : earlyfordstore@verizon.net
- Thousands More parts being added online daily
Flywheel Dowel Retainer Ring
A-7609
Regular price $3.50 Save $-3.50/
Modern Front Timing Cover Seal 1928-48
A-6700-M
Regular price $20.00 Save $-20.00/
- One Piece Neoprene Rubber
- Seals Front Crankshaft Snout
1935-1948 Dropped Steering Arms
48-3134/5
Regular price $125.00 Save $-125.00/
Sold as a Pair.
These forged steel aftermarket bolt on steering arms fit all 1937-1948 spindles. This style arm is the kind most commonly used on 1935-1948 front ends with dropped front axles.
These steering arms bend downward, so that the steering tie rod fits below the front radius rod/wishbone. For most 4" inch dropped axles, the arms on the original Ford spindles are not long enough to be heated and bent down as far as necessary to clear the radius rod/wishbone. Many people will cut the arms off of their original spindles and use these arms for that application.
* If you require that your tie rod fit above the front radius rod/wishbone you can use our other steering arms with part number "B-3134", the arms bend upward a small amount.
* These spindles drop down 4" inches from the center of the bolt holes where they bolt to the spindle, to the bottom part of the arm, where the tie rod bolts onto them.
These forged steel aftermarket bolt on steering arms fit all 1937-1948 spindles. This style arm is the kind most commonly used on 1935-1948 front ends with dropped front axles.
These steering arms bend downward, so that the steering tie rod fits below the front radius rod/wishbone. For most 4" inch dropped axles, the arms on the original Ford spindles are not long enough to be heated and bent down as far as necessary to clear the radius rod/wishbone. Many people will cut the arms off of their original spindles and use these arms for that application.
* If you require that your tie rod fit above the front radius rod/wishbone you can use our other steering arms with part number "B-3134", the arms bend upward a small amount.
* These spindles drop down 4" inches from the center of the bolt holes where they bolt to the spindle, to the bottom part of the arm, where the tie rod bolts onto them.
![Flywheel Mounting Bolts 1928-1953 (Sold Each) [A-6376]](http://www.earlyfordstore.com/cdn/shop/products/A-6376_{width}x.jpg?v=1609889647)
Flywheel Mounting Bolts 1928-1953 (Sold Each) [A-6376]
A-6376
Regular price $4.95 Save $-4.95/
These bolts are SOLD EACH. These are the special bolts that are used when bolting the flywheel onto the end of the crankshaft.
4 Required
4 Required
1928-1948 Flywheel Ring Gear
B-6384
Regular price $35.00 Save $-35.00/
Brand new flywheel ring gear. Fits 1928-48.
1942-48 Dist. Gasket Set
21A-12104
Regular price $8.95 Save $-8.95/
1933-1934 Engine Mount Adapters (When Using 1937-1953 Flathead V8 Engines
41A-6023
Regular price $59.95 Save $-59.95/
1935-48 CAR & 35-47 PICKUP CLUTCH RELEASE BEARING HUB
48-7561
Regular price $25.00 Save $-25.00/